BMW E46 M3 PnP Kit
BMW E46 M3 PnP Kit
BMW E46 M3 PnP kit offers easy way to install engine management system. It's based on powerful Syvecs S6Plus that offers a lot of tuneability. Full kit including ECU and Adapter loom
The S6-I ECU offers an extremely high level of precise engine management control. The triple processor unit uses a high speed RISC processor for code execution and an additional large FPGA for high speed engine position tracking, allowing the scheduling of code to be independent of signal patterns, increasing flexibility, efficiency and accuracy under transient conditions. This powerful combination also allows advanced control algorithms but yet easy to map for the end user still using our SCal software and S6 Firmware.
Designed to cater for PnP kits where clients need only the I/O of the S6GP but also need the programmable CAN Bus and Drive-By-Wire support offered by the S6Plus.
Ask for price!
- Pick up from local Finnish post office
- 6,90 €
- DHL Express Suomi
- 15,00 €
- EMS Express Worldwide
- 39,00 €
- Parcel will be delivered to receivers home adress, after possible customs handling. International Express Mail service, handled by local mail companies around the world.
Your order can be shipped with these shipping methods.
The Syvecs BMW E46 M3 Kits brings a new level of Engine Management control to the BMW M3 Range
Compatible Only with Manual Transmission
By simpling pluging in the kit a whole new level of control is available, offering the following and more!
- Live Tuning of every aspect of the engine’s calibration
- Ability to select desired engine map, boost level, traction and launch control levels through 12 Position switch
- Fully adjustable Launch control with Anti-lag strategies and Ramp in Maps
- Full Vanos Control
- Closed loop Dual Lambda Control with LSU4.9 (Sold Separately)
- Flex Fuel control
- Cruise Control add on
- Control the OEM Injectors and additional injectors for high power installations where staged injection may be required
- Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temperatures etc
- Monitor and trimming of exhaust gas temperatures
- Built in data logging using a market leading analysis software of up to 8 hours, with data rates at up to 1000hz
- Rolling Antilag / Pit lane limiter strategies, great for building boost on a roll
- Antitheft and valet modes
- Super fast connection via RJ45 Ethernet port for live tuning anywhere in the world or evenremotely if on track if connected to a wireless unit.
- Adjustable traction control strategies based on lateral g, steering angle and/or individual wheel speed monitoring.
- 4 programmable and selectable target slip maps. An immediate torque reduction can be applied by the ECU via ignition retard or a fuel cut.
- Configurable Engine Safety Trips on all important parameters like oil temperature, oil pressure.
- Fuel pump control of both main Direct Injection pumps, and sub pumps, as well as Relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost.
- 4 different Pedal to Throttle Angle maps with multipliers for different parameters e.g. speed. Again adjustable via steering wheel buttons
- Configurable individual cylinder closed loop knock control, to suit any cylinder modification with adjustments to frequency, windows for listening and gains for each cylinder. Ability to trigger full cylinder shutdown in severe knock conditions.
- Flat Shift
- Ability to change Torque ramp in after launch
- Change throttle blip requests to match your torque band. Especially useful on oversized turbo installations.
- Run up to 7bar map sensors
- Control high or low impendence injectors
- Change injector dead times based on voltage levels for proper control
- Change injector end angle to ensure injection point is properly calibrated
- Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position
- Ability to use any size DBW throttle body e.g. Chevrolet LS7
- Wet and Dry – Wet and Dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring
- Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves
- Connect any race series dash or even one of our partners’ Touchscreen CANBUS adjustment /display units
- View any input live with built in scope up to 1000hz • And much, much more!